Kyosho 30639 1/12 Plazma Mk Iii Limited Alpha-2 2WD Electric RC Car

Product Introduction: Shunfooti 2WD racer running the classic 1/12 on road car is back in full. In the 1980s, the Phantom EP-4WD series sold by Kyosho, the 1/12 scale on-road car was a flow-shaped category of electric R/C car racing. However, the Phantom had powerful rivals. It was a plasma series of rear 2-wheel drive drives from the same Kyosho. This Plasma Mk III Limited, is the ultimate form of the 1980's plasma series, has been back for over 30 years since its release in 1987! This reproduction model faithfully reproduces the original design just like other Kyosho vintage series, but has been improved to accommodate modern R/C mecha and power sources, so you can enjoy the running as your current model. With the use of common components with the Phantom EP-4WD Ext, the simpler construction makes the vehicle lighter and faster than Phantom on circuits with sufficient surface grip. The main chassis is made with the same carbon fiber as the original, but the original black FRP upper plate and the joint bar for holding A-bar. The differential unit equipped with the rear axle has been reborn into a more luxurious and high performance machine including the first equipment for the 60th anniversary of the Phantom EP-4WD Ext. Front suspension features a simple kingpin spring with adjustable caster angles. Furthermore, the reprint includes two kingpins with slightly different outer diameter for fine maneuverability. The body has been recreated with an open cockpit type α-2 with excellent aerodynamics, and the New Plasma MkIII Limited brings a new spin to the Kyosho Vintage Series. The attractive rear 2WD 1/12 racer has been reproduced in the 16th release of the Kyosho Vintage Series. A reproduction of the Limited Edition model released in 1987 as a racing model. The original design of the 1987 model has been updated to match the modern R/C mecha and power source. The 1/12 EP racer employs a standard and reliable 3-point suspension system. Rigid carbon main chassis and upper plates are equipped with FRP rear A-bars for improved tire gripping power. Kingpin spring front suspension for changing handling feel Dial rear oil damper for easy spring tension adjustment Uses a ball def that can be effectively adjusted by tightening the nuts. Equipped with a lightweight and high strength φ6 carbon rear shaft. Assembly chassis kit with glued trimmed front and rear tires and unpainted bodies. Technical Data: Total Length: 13.4 inches (340 mm). Overall width 172mm Total height 83mm Chassis Type 3P Susan Direct Drive Wheelbase 203-204mm (Adjustable) Tread F:137mm/R:133mm Tire F: φ48×23mm/R: φ53×35mm Gear Ratio 3.38:1 Total weight (approx.): 30.9 oz (850 g) (when equipped with GAB4202). Maximum speed: Approx. 11.3 mph (55 km/h (when equipped with Le Mans 480 G). Running time: Approx. 23 minutes (when equipped with Le Mans 480G) *Varies depending on operating conditions. [Kit Contents] 1 chassis part set. Pre-glued tires Unpainted body Decal Foil Wrench (12/4.0) 5.5/5.0 Wrench Caster Corner Jig Shock Wrench (Requires) Each company has a 2-channel transmitter and receiver servo. Speed Controller 540 Motor running battery Transmitter Battery running battery charger body paint Batteries, batteries, and battery charger are required to power this product, but are not included. Also, this product does not include the motor, transmitter, batteries for transmitter, RC mecha (receiver, ESC, servo, etc.) Additional parts are purchased, assembly and painting are required before riding. This product does not include fuel, paint, glue, tools, etc. Safety Warning: Please drive in a wide and safe location such as circuit for RC cars. Never run on the road. Do not run near crowds, parks or small children. Do not run in narrow spaces or indoors. Do not run in schools, hospitals, homes, and other places where it can disturb others. Do not run at night or early morning

• The Shunfooti 2WD racer is back in full form of the 1/12 on-road car